Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Temple City
Gate installation in Temple City costs between $3,800 and $9,500 for a typical motorized driveway gate, with sliding gates running $4,200-$8,000 installed and pedestrian gates starting around $1,600. Most Temple City projects take two to three days, and we keep one side of the driveway open the entire time so you’re never blocked in. Our Gate Installation team works on the 1950s-1970s ranch homes that dominate this city every week, so we know what those narrow driveways and shallow footings demand. Call (562) 267-0589 and we’ll schedule a free measure, then hand you a written price before any work starts.
Why Vance Gate Repair Arcadia Is Temple City’s Preferred Gate Installation Company
Gate Repair in Temple City is what homeowners call us for because we show up with a name, a photo, and a written scope of work before a single tool leaves the truck. Adrian Vance started this company in 2014 doing commercial access-control documentation, and that habit carried over: every Temple City job leaves with a photo log of what we found, what we set, and what we installed. You don’t pay twice to rediscover a problem someone else should have documented the first time.
We work the tight sites this city is known for. Shared driveways off Las Tunas Drive. Narrow side yards where a swing gate arc would clip a car bumper. Liquid amber roots pushing slide tracks out of level. When a homeowner on a post-WWII tract lot asks whether they can fit a motorized gate, we measure first and answer honestly, because forcing a swing gate onto a 9-foot-wide driveway is how you get scrape marks on the fender and a hinge post that leans by spring.
Response time to Temple City is same-day or next-day for repairs, and installation measures are typically scheduled within 48 hours. A live person answers (562) 267-0589 at any hour. No voicemail loop, no callback queue. The 365-Day Done Right Promise applies to every gate we install in Temple City: if it’s not right within the first year, we make it right at no additional charge.
Our Gate Installation Services in Temple City
Driveway Gate Installation
Driveway gates on Temple City ranch homes almost always replace a gate that was added decades after the house was built. That means the original post footings are shallow, the concrete is cracked, and the driveway width was never planned around a gate arc. We pour new reinforced footings when needed, set the posts plumb, and build the gate to clear your actual driveway dimensions, not a catalog spec. Most driveway gate installations in Temple City run $3,800-$7,500 depending on material, width, and whether we motorize it.
Pedestrian Gate Installation
Pedestrian gates in Temple City serve a real security function, and they’re also the gate most likely to sag because they get used constantly and installed cheaply in the first place. We build pedestrian gates with welded frames and reinforced hinge posts, sized to the opening rather than trimmed to fit. A new steel pedestrian gate with a keypad entry typically runs $1,600-$3,400 in Temple City. The price is written and handed to you before we start, under Haven Standard Clause 1.
Sliding Gate Installation
Sliding gates are the rational choice for most Temple City lots, because the driveway width that worked fine for a 1962 Chevy does not leave room for a swing gate arc today. The catch is the city’s tree canopy. Liquid amber and camellia roots heave the concrete pad beneath slide tracks, throwing the rail out of level until the operator grinds and stalls. When we install a slide gate in Temple City, we pour the track pad with deeper reinforcement than a standard install and set the rail on leveling shims so minor heave can be corrected without tearing everything out.
Swing Gate Installation
Swing gates still make sense on Temple City properties with wider frontages, the ones near the southern edge of the city or on corner lots with a longer setback. We measure the full arc before recommending one, because a swing gate that clears in Arcadia often will not clear here. If a swing gate fits your site, we build it heavy, set the hinge posts on poured footings, and photograph the post depth before concrete covers it. You keep that evidence in your job file.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterTrusted Brands We Service in Temple City
We work on whatever motor is already on the property. That matters in Temple City, where a wave of gate installations in the 1990s and 2000s means homeowners now have aging LiftMaster, DoorKing, and FAAC operators bolted onto pads that were never designed for them. We service nine automation brands, including FAAC, BFT, Linear, Viking, and Ghost Controls in Temple City, so you’re not steered toward replacing a good motor when a properly set limit switch or a new photo-eye fixes it. We keep common replacement parts for these brands stocked for Temple City jobs, which shortens repair turnaround on operators that would otherwise wait a week for a part.
Common Gate Installation Problems We See in Temple City Homes
- Root heave under slide-gate tracks. Liquid amber and camellia roots are relentless in Temple City. They push the concrete pad under the track out of level, and the gate grinds to a stop because the rail is now 3/8 inch high in the middle. We cut expansion joints and pour deeper pads to buy years of stability.
- Undersized post footings from the original 1950s driveway. The gate is heavy, the footing is 18 inches of cracked concrete, and the hinge post leans a little more each year. We see this on swing gates all over the north side of Temple City. The fix is a new 30-inch reinforced footing and a post set plumb.
- Narrow driveways that were never meant for a gate arc. A swing gate that clears in El Monte will scrape a car bumper on a 9-foot-wide Temple City driveway. We measure the arc and tell you the truth before you spend money on the wrong gate.
- Santa Ana wind stress on gate frames. October and November bring wind that funnels hard through the San Gabriel Valley floor. Slide gates get blown off misaligned tracks, and swing gates get slammed against their stops until hinge welds crack. We brace frames and check track alignment before wind season hits.
Pricing for Gate Installation in Temple City, CA
Here’s what Temple City homeowners should expect to pay, in writing, before work begins. A motorized sliding driveway gate runs $4,200-$8,000 installed. A swing driveway gate runs $3,800-$7,500. A pedestrian gate with keypad entry runs $1,600-$3,400. Motor and operator replacement on an existing gate runs $950-$2,600 depending on brand and whether the arm bracket is intact. A double gate, common where two driveways share a single wide curb cut, runs $7,500-$11,500. What changes the price most in Temple City is the footing work: if we’re cutting out old 1950s concrete and pouring a reinforced pad, that’s real labor and real material, and it’s the part that determines whether the gate lasts 20 years or leans in five. Call (562) 267-0589 for a free measure and a written estimate. The price you’re quoted is the price you pay, agreed before any work starts.
We Also Serve Cities Near Temple City
Our crews work throughout the San Gabriel Valley. Beyond Gate Installation in Temple City, we regularly install and repair gates in El Monte, San Gabriel, Arcadia, and Rosemead. If you’re on the border near Rosemead Boulevard or south of Las Tunas, you’re still in our coverage area with the same written pricing and documentation standard.
Serving Temple City, CA - Our Local Coverage Area
We’re based in the Temple City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Installation in Temple City
Your gate is jumping the track because the track itself is no longer level, and in Temple City the usual cause is root heave from liquid amber or camellia trees pushing the concrete pad upward. A misaligned track catches the gate wheels and throws the gate off the rail. Call (562) 267-0589 and we’ll level the track, shim the rail, and tell you whether the pad needs to be repoured or just repaired.
Usually not, and we’ll tell you that before you spend money. A swing gate needs a full arc of clear space, and Temple City shared driveways off streets like Las Tunas Drive rarely have it. The gate either swings into a neighbor’s landscaping or blocks the sidewalk. A sliding gate is the practical answer on most shared driveways. We installed a Viking slide gate on a shared driveway off Las Tunas where a swing gate would have swung into the neighbor’s camellia hedge. The old DoorKing post footing was 18 inches deep, so we poured a 30-inch reinforced footing, added a safety photocell and keypad entry, and finished in two days keeping one side of the driveway open the whole time. Call (562) 267-0589 for a free measure.
The post footing is almost certainly too shallow for the gate hanging on it, and the installer either did not check the depth or did not want to charge you to fix it. Temple City’s original ranch homes were built without gates; the posts were added decades later, often with 18 inches of concrete that cracks under a heavy iron gate. We pull the post, pour a 30-inch reinforced footing, and photograph the depth before concrete goes in. That photo record is yours under our documentation standard. Call (562) 267-0589 for a written assessment.
The wind is not killing the operator. The wind is pushing the gate against misaligned stops and tracks, which increases load on the motor until the thermal overload trips or the gear strips. In Temple City the pattern is predictable: October brings the first strong Santa Ana event, the gate gets blown off a slightly out-of-level track, and the operator burns itself fighting the resistance. We fix the track and stops first, then check the operator. Call (562) 267-0589 before October if you want to skip this year’s version of the problem.
Yes. The photocell, also called a photo-eye, is the infrared beam that stops the gate if anything crosses the path while it moves. A pedestrian gate is short, and a child or a pet is exactly the height the gate catches if the beam is missing. California code does not exempt short gates, and neither do we. Every automated gate we install in Temple City includes a safety photocell, and we photograph the beam alignment before we leave. Call (562) 267-0589 and we’ll check your existing beam.
Contact Vance Gate Repair Arcadia for Gate Installation in Temple City
If you live in Temple City and you’re planning a gate installation, start with a free measure and a written price. We’ll assess your driveway width, check the existing footings, tell you whether a slide or swing gate fits, and hand you a line-item quote before any work begins. You’ll also get a documented photo record when the job is done, walking you through what was found, what was set, and what was installed. That’s the way we’ve worked since 2014, and it’s the reason Temple City homeowners keep our number. Call (562) 267-0589 now. A live person answers, and the estimate costs you nothing.
Written by Adrian Vance, Owner at Vance Gate Repair Arcadia, serving Temple City since 2014.