Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Repair in Temple City, CA
Gate access control problems in Temple City usually trace back to aging keypads, misaligned photo-eyes, or corroded wiring on operators installed decades after the original tract homes were built. We fix them same-day, with a written price before any work starts. Call (562) 267-0589 and a live person answers.
Why Temple City Homes Are Different
Temple City’s post-WWII ranch homes on 5,000 to 7,500 square foot lots rarely had gates when they were built between the 1950s and early 1970s. The gates came later, bolted onto narrow single-car driveways where swing clearance is tight and post anchors vary wildly in depth. We find original concrete pads that were never meant to hold a 400-pound steel gate, so hinge and post work here is a structural job, not a hardware swap.
Hard San Gabriel Valley water corrodes hinge pins and roller bearings faster than most homeowners expect. Fall Santa Ana winds funnel through the SGV floor and push slide gates off misaligned tracks every October. And the camellia and liquid amber roots that give Temple City its tree canopy heave the concrete beneath slide-gate rails, throwing them out of level and grinding operators to a stop. These are the failure patterns we see most.
Our Main Temple City Services
Most Temple City calls start with a gate that won’t open or a motor that runs but won’t move the gate. These three pages cover the work in detail.
Gate Repair in Temple City
When a gate sags, binds, or stops mid-travel in Temple City, the cause is usually a failed hinge, a heaving track, or a limit switch that drifted. We reset hardware and photograph every adjustment so you don’t pay twice to rediscover the same problem. See Gate Repair in Temple City for full repair detail.
Gate Installation in Temple City
New gate work in Temple City means planning around narrow 1950s driveways and root-prone tree lines. We measure, quote in writing, and install gates sized for the actual clearance, not an optimistic guess. See Gate Installation in Temple City.
Gate Motor & Opener in Temple City
Older Viking, LiftMaster, and DoorKing operators across Temple City are hitting the end of their 15 to 20 year service life at the same time. We service nine automation brands and repair before we recommend replacement. See Gate Motor & Opener in Temple City.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
BeforeAfterGate Access Control in Temple City
Gate access control in Temple City means the keypad, remote, intercom, or card reader that tells the gate to move. On 1990s and 2000s operators bolted onto older tract homes, the weak points are usually corroded keypad terminals, dead remote receivers, and phone-entry boxes that no longer talk to the motor. We repair and replace these systems on all nine major automation brands, and every visit includes a documented photo record. For a fuller look at the discipline, see Gate Access Control.
Keypad Entry
Signs you need it
The keypad accepts some codes but not others, or the buttons work intermittently after rain.
What it costs in Temple City
Keypad and intercom repair in Temple City typically runs $240 to $520; full replacement with a new weather-sealed keypad usually falls between $520 and $850.
How we do it
We test the keypad at the terminals, clean or replace corroded connections, reprogram codes, and photograph the settings.
Phone Entry
Signs you need it
The call box rings a phone that doesn’t exist, or the gate opens for every call regardless of the code.
What it costs in Temple City
Phone entry repair here ranges from $340 to $700; full replacement with a cellular or VoIP-compatible unit runs $1,100 to $2,000.
How we do it
We identify whether the fault is wiring, the phone line, or the board, then repair or replace and log the settings in the job record.
What Gate Access Control Costs in Temple City
| Item | Typical range in Temple City |
|---|---|
| Keypad and intercom repair | $240 - $520 |
| Phone entry or video intercom replacement | $1,100 - $2,000 |
| Keypad or remote replacement | $520 - $850 |
How long does a gate access control repair take in Temple City?
Most keypad and remote faults are fixed in one visit, typically under two hours. Phone entry and video intercom replacements may require a second visit if a new board has to be ordered. Call (562) 267-0589 for a written price before we start.
Can you add a remote control to an older Temple City gate operator?
Usually yes. We install aftermarket receivers on Viking, FAAC, Linear, and most other operators. The receiver is programmed on site and the codes are documented. Call (562) 267-0589 for a free estimate.
Gate Parts & Welding in Temple City
Gate parts and welding in Temple City are dominated by rust, mineral-heavy water, and root movement under posts and rails. A gate that worked fine in May grinds to a stop in November because Santa Ana winds finally separated a fatigued weld joint. This is where our Gate Parts & Welding work comes in: we replace load-bearing steel and match new parts to old geometry.
Hinge Replacement
Signs you need it
The gate sags on the latch side, scrapes the ground, or the hinge pins show visible rust streaks.
What it costs in Temple City
Heavy gate hinge replacement in Temple City typically runs $240 to $520 per hinge depending on weight and access.
How we do it
We unload the gate, cut or unbolt the old hinge, weld or bolt the new one in place, and photograph the alignment.
Rail Repair
Signs you need it
The slide gate shudders mid-travel or jumps the track where the concrete pad has settled.
What it costs in Temple City
Cantilever gate roller and rail repair in Temple City typically runs $240 to $520 for the mechanical work; concrete pad replacement runs $700 to $1,500.
How we do it
We level the rail, replace worn rollers, and document the new track position with photos and measurements.
What Gate Parts & Welding Costs in Temple City
| Item | Typical range in Temple City |
|---|---|
| Heavy gate hinge replacement | $240 - $520 per hinge |
| Cantilever gate roller and rail repair | $240 - $520 |
| Concrete pad replacement for a slide gate | $700 - $1,500 |
Can you weld a cracked gate frame without removing it in Temple City?
Yes, in most cases we weld in place after bracing the gate square. For severe fatigue cracks, removing the gate leaf gives a stronger repair. Call (562) 267-0589 for a written quote before we start.
Do you replace just the hinge, or do we need a whole new post?
We replace only what has failed. If the post concrete is cracked or the post moves, we address the footing rather than selling a full rebuild. Call (562) 267-0589 for a free estimate.
Brands We Service in Temple City
We service FAAC, BFT, Linear, and Viking operators across Temple City, along with five other major automation brands. Common boards and receivers are stocked locally, so most replacements happen same-visit. See our brands for the full list.
Pricing for Gate Repair in Temple City, CA
| Service | Typical range in Temple City |
|---|---|
| Keypad and intercom repair | $240 - $520 |
| Keypad or remote replacement | $520 - $850 |
| Phone entry or video intercom replacement | $1,100 - $2,000 |
| Heavy gate hinge replacement | $240 - $520 per hinge |
| Cantilever gate roller and rail repair | $240 - $520 |
| Concrete pad replacement for a slide gate | $700 - $1,500 |
Prices in Temple City run higher when posts have to be excavated or wiring is buried under root-heavy camellia beds. On every job, the flat price is written and handed over before any work starts, with no surprise invoice at the end.
Neighborhoods We Serve in Temple City
We cover the whole city, from the streets above Las Tunas to the newer developments south of the park and everything along Rosemead Boulevard. Most Temple City calls get a same-day visit.
- North Temple City
- Central Temple City
- East Temple City
- South Temple City
- West Temple City
Service Area - Cities Near Temple City
We also serve El Monte, CA, San Gabriel, CA, Arcadia, CA, and Rosemead, CA. Dispatch and scheduling are coordinated from our Los Angeles office, and crews serve Temple City locally.
Serving Temple City, CA - Our Local Coverage Area
We’re based in the Temple City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Temple City
Most Temple City calls are answered live and scheduled for same-day or next-morning service. Emergency lockouts and security failures get priority. Call (562) 267-0589 and a person answers, not a voicemail.
Most repairs and like-for-like replacements don’t need a permit. New automated gate installations may need city approval depending on the location and electrical run. We handle the paperwork on the jobs that require it.
Yes. We service Viking, LiftMaster, FAAC, DoorKing, Linear, and four other brands regardless of who did the original install. We bring a written price and a photo log, not a replacement pitch.
Call (562) 267-0589 for a free estimate on gate access control or parts and welding work in Temple City. A live person answers 24/7, the price is written before we start, and the repair is covered by the 365-Day Done Right Promise.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Temple City Customers Say
"They installed the opener and left me a diagram of the wiring and the limit settings. When I needed a second remote programmed I could do it myself."
- Nadine C."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R."Gate had been dragging for a year. They photographed the bent hinge post, explained why the operator kept faulting, and gave me a fixed price to correct both."
- Terrence B.